If you are not satisfied with search results, try browsing categories manuallyHere they exist two regulator circuits, that use the IC L200, as regulator of voltage and current, the company SGS-Thomson, which give these circuits. In circuit Fig.1, we can regulate the output voltage, with the... [more]
There are many circuits for low voltage regulators. For higher voltages, such as supplies for valve circuits, the situation is different. That’s why we decided to design this simple regulator that can cope with these... [more]
circuit from:http://www.extremecircuits.net/2010/06/high-voltage-regulator-with-short.html
The LM317T is a adjustable 3 terminal positive voltage regulator capable of supplying in excess of 1.5 amps over an output range of 1.25 to 37 volts. The device also has built in current limiting... [more]
The LM317T output current can be increased by using an additional power transistor to share a portion of the total current. The amount of current sharing is established with a resistor placed in series with... [more]
People often forget that many voltage regulator ICs have an upper limit (usually 35 V) on the input voltage they can handle. That applies primarily to types with a fixed output voltage. Adjustable voltage regulators... [more]
circuit from:http://www.extremecircuits.net/2010/05/protection-for-voltage-regulators.html
This device is designed to be a simple, inexpensive ‘comparator’, intended for use in a solar cell power supply setup where a quick ‘too low’ or ‘just right’ voltage indicator is needed. The circuit consists... [more]
circuit from:http://www.extremecircuits.net/2010/05/solar-cell-voltage-regulator.html
This circuit has proven to be useful to indicate when the voltage in a power supply line is changing from 120V to 240Vac. It can be used in different circumstances and circuits, mainly when an... [more]
Connecting this circuit to the battery of your vehicle, you will always know at a glance the approximate voltage available. An indication of battery voltage is useful to the motorist for monitoring the battery's capacity... [more]
circuit from:http://www.extremecircuits.net/2009/08/battery-voltage-indicator-circuit.html
This simple circuit tests speakers, microphones, transformers and voltage. It's basically a very low frequency oscillator that produces extremely short 'fruity' pulses. The type of sound produced is very easy to hear and to determine... [more]
circuit from:http://www.extremecircuits.net/2010/01/components-voltage-tester-circuit.html
This circuit is not a novelty, but it proved so useful, simple and cheap that it is worth building. When the positive (Red) probe is connected to a DC positive voltage and the Black probe... [more]
circuit from:http://www.extremecircuits.net/2009/08/dc-or-ac-voltage-indicator-circuit.html
Many times we needed a variety of voltages, from a battery 12V. With the circuit, we can take voltages smaller or bigger, positive or negative, from a battery 12V. [more]
The fixed voltage power supply is useful in applications where an adjustable output is not required. This supply is simple, but very flexable as the voltage it outputs is dependant only on the regulator and... [more]
The power line fluctuations and cut-offs cause damages to electrical appliances connected to the line. [more]
Can be used agains ferocious animals or attackers, BUT REMEMBER, this device may be illegal in your state. [more]
This low voltage circuit can be used to monitor batteries and other volatile sources of current for problems. The circuit sounds an alarm and lights an LED, but can be interfaced to any number of... [more]
Sometimes you have a situation where you have a 5-V supply voltage but part of the circuit needs a lower supply voltage. A voltage regulator from the Texas Instruments TPS62000 family [1] is a good... [more]
circuit from:http://www.extremecircuits.net/2010/05/low-voltage-step-down-converter.html
In this circuit a LM339 quad voltage comparator is used to generate a time delay and control a high current output at low voltage. Approximatey 5 amps of current can be obtained using a couple... [more]
All miniature electronic devices operate off batteries. Some of them need higher than the standard battery voltages to operate efficiently. If the battery of that specific voltage is unavailable, we are forced to connect additional... [more]
circuit from:http://www.extremecircuits.net/2010/05/low-power-voltage-doubler-booster.html
Here’s a project that could be useful this summer on the beach, to stop anyone touching your things left on your beach towel while you’ve gone swimming; you might equally well use it at the... [more]
circuit from:http://www.extremecircuits.net/2010/05/mini-high-voltage-generator.html
The opamp is wind as a voltage comparator, with a reference voltage applied to pin 2 and the test voltage applied to pin 3: the relay turns on when the pin 3 voltage exceeds that... [more]
Flying hand launch gliders means living with small capacity receiver NiCad battery packs. These small packs are light, but have the distinct disadvantage of rapidly depleting. You can carefully time your flights, but you end... [more]
Here is another equally cool low voltage alarm circuit for your glider receiver battery. [more]
A simple but less efficient methode of controlling a DC voltage is to use a voltage divider and transistor emitter follower configuration. [more]
This is a fun and useful circuit for demonstrating high frequency high voltge. It can produce up to about 30KV, depending on the transformer used. It is cheap and easy to make, thanks to the... [more]
Many times we needed symmetric voltage, but we do not have the possibility him of taking immediately, from a existing supply. Then it will be supposed him we create from the existing single. [more]
This circuit is not a novelty, but it proved so useful, simple and cheap that it's worth building. [more]
Another method of using opamps to regulate a power supply is shown. The power transformer requires an additional winding to supply the op-amps with a bipolar voltage (+/- 8 volts), and the negative voltage is... [more]
This circuit uses an LM11 to form a voltage follower with 1G ohm input resistance built using standard resistor values. With the input disconnected, the input offset voltage is multiplied by the same factor as... [more]
This simple and inexpensive circuit can produce a dual (positive and negative) voltage from a single supply input. It is therefore extremely useful for powering opamp and other circuits that require a dual voltage from... [more]
When the input voltage is 0 the LED glows. The LED stops glowing when the voltage rises to the level determined by R2. Reverse + and - pins to reverse operating mode. To set voltage... [more]
A voltage window switch is in practice the basic lower window limit of this circuit is roughly 3V and the upper limit is 9V. The window range can be extended by fitting a suitable range [more]
Most off-the-shelf car battery chargers cannot not be left connected to the battery for long periods of time as over-charging and consequent battery damage will occur. This add-on circuit is placed in series with the... [more]
circuit from:http://www.extremecircuits.net/2010/05/battery-charger-regulator.html
This is a combination digital clock timer and solar panel charge controller used to maintain a deep cycle battery from a solar panel. The timer output is used to control a 12 volt load for... [more]
This adaptor circuit is essentially a 100mA constant current source. It is applied across a low-value resistor of unknown value (ie, the resistance to be measured) and the resulting voltage drop can then be measured... [more]
circuit from:http://www.extremecircuits.net/2010/05/low-ohms-adaptor-for-dmms-based-on.html